Ames Performance Engineering - Click Here!

POCI LINKS

2017 Annual Convention - Click Here! Visit the POCI Club Store - Click Here! Join us on Facebook - Click Here! Join us on Pinterest - Click Here! Vist the POMARC - Click Here!

Advertise on POCI.org

Search:

Type: Posts; User: Tinindian

Search: Search took 0.01 seconds.

  1. Replies
    0
    Views
    1,989

    1931 crank hole cover

    Stainless one piece Series 401 crank hole cover. In good condition. Has some marks that I believer could be removed. $350.00 including shipping. Email me for pictures. Contact rhpti@telus.net
  2. Replies
    1
    Views
    1,776

    Any reputable hardware supplier will have nuts...

    Any reputable hardware supplier will have nuts that fit your axle. They will just be hex nuts rather than square. I bought new ones a couple of years ago for about $1.50 each from Aclklands here in...
  3. Replies
    1
    Views
    1,663

    Loosen three nuts on generator brackets (one on...

    Loosen three nuts on generator brackets (one on engine block, one on bracket at generator and one underneath generator. Tip generator towards the block. Install belt, pull generator outwards to...
  4. Thread: 1930 coupe

    by Tinindian
    Replies
    1
    Views
    1,637

    Bob's Automobilia sells them for Buicks. Same...

    Bob's Automobilia sells them for Buicks. Same diameter just order the correct length.
  5. Thread: 31 Fuel Pump

    by Tinindian
    Replies
    1
    Views
    1,561

    I just had my fuel pump rebuilt by Hal Houghton. ...

    I just had my fuel pump rebuilt by Hal Houghton. Excellent job, good price and quick service. houghton@classicpreservation.com
  6. Thread: Engine Swap

    by Tinindian
    Replies
    1
    Views
    1,483

    I have seen many 29 and 30 engines in earlier...

    I have seen many 29 and 30 engines in earlier Pontiacs, ones that were changed 50 or 60 years ago. If you have Hotchkiss drive there should be no problems. If your car is an early 28 (12 spoke...
  7. Thread: Spindles

    by Tinindian
    Replies
    0
    Views
    1,252

    Spindles

    I am looking for two steering knuckles (spindles for my 1930 Pontiac. Mine are both cracked. Sure would like to be able to drive my car when I am finished rebuilding my engine.
  8. Replies
    0
    Views
    1,225

    Steering Knuckle

    Any help appreciated. I need two steering knuckles (spindles) for a Series 6-30B Pontiac. Apparently 30-32 are the same.
    I have almost finished rebuilding my engine and would like to be able to...
  9. Replies
    1
    Views
    1,962

    Tim I am interested in some of these parts. I...

    Tim
    I am interested in some of these parts. I have sent you an email. Did you recieve it???
    Thanks
  10. Replies
    2
    Views
    1,760

    On the left side of the engine, on the flywheel...

    On the left side of the engine, on the flywheel housing above the starter there is a round plug (about 2" in diameter). If you remove this plug (it just pulls out) you will see a round pointer and...
  11. Replies
    0
    Views
    1,199

    Harmonic Balancer

    I need an harmonic balancer for my 1930 Pontiac. The parts book suggests that 29-30 and 31 are all the same. Any help or leads are appreciated. I also need six pistons 3 5/16 .040 os and a left...
  12. Thread: Paint Colour

    by Tinindian
    Replies
    0
    Views
    1,324

    Paint Colour

    My engine is out to be overhauled. I am planning on painting it. Can anyone suggest as fact, fiction or fantasy wether the acessories (brackets, oil filler and water manifold) were/are/should be...
  13. Replies
    1
    Views
    1,901

    Leaking rear main bearing

    My Series 6-30B just recently and quite suddenly my rear main bearing has started to leak. There is no rear main seal, just a grove in the block and cap behind the bearing itself. I cannot remember...
  14. Thread: 31 Brakes

    by Tinindian
    Replies
    1
    Views
    1,980

    The shop manual has very clear directions on...

    The shop manual has very clear directions on adjusting Midland Steeldraulic Brakes. I also have a manualput out by them and one by Raybestos.
  15. Replies
    5
    Views
    3,157

    NAPA has them is stock up here in Canada.

    NAPA has them is stock up here in Canada.
Results 1 to 15 of 15